RTS XCP-ADAM-MC Servisní příručka Strana 1

USER INSTRUCTIONSKP-32 KEYPANELEKP-32 EXPANSION PANELLCP-32 LEVEL CONTROL PANELCall waitingMicHeadsetVol .MENUFWDBACKMUTE CLR PGMNU MSLIST1PLIFB2AU TO

10Switch 6: Not DefinedDefault Setting: Open.Switch 7: Test/DebugDefault Setting: Open.Switch 8: Test/DebugDefault Setting: Open.ADDRESS SWITCH SETTIN

11Each LCP-32 adjusts the listen levels for 16 keypanel keys, and you can connect as many LCP-32 panels asrequired to adjust all keys on the KP-32 and

12Power Supply ConnectorAlign and insert the external power supply connector. Tighten the locking ring. Connect a power cord tothe power supply and to

13BASIC KP-32 OPERATIONSCREEN SAVER OPERATIONIf the KP-32 is set for screen saver operation, the alphanumeric display automatically shuts off after se

14Continuous Red Talk LED ("In-use"): The key is off, but someone is talking to the destination. Thisindication is provided for any local PL

15For latching operation (if enabled) tap a key; it will turn on and remain on. Tap the key again to turn it offwhen finished.☞ Latching may be turned

16☞ Solo key setup / display: "Key Option Menu, Solo", page 36.Operation of Intercom Talk Keys with the Speaker DIM SettingActivating any ta

17TELEPHONE OPERATION☞ Note: Telephone operations require an optional TIF-951 Telephone Interface. Also, you must firstassign an intercom key to talk/

18c. Tap the TIF talk key. The TIF key talk and listen indicators will turn off and the TIF-951 "OFF"LED will activate. The TIF-951 is now r

195. Hang up using theKP9X hang-up sequence, page 17.DIALING AND HANGING UP USING THE KP-32 DIALING MENUThe dialing menu will only activate when talki

2PROPRIETARY NOTICEThe RTS product information and design disclosed hereinwere originated by and are the property of TelexCommunications, Inc. Telex r

20☞ Note: Occasionally, you may receive intercom an intercom caller name in the Call waiting windowwhile you are talking on the phone. In this case, t

21KP9X SERIES KEYPAD PROGRAMMING☞ A summary of the keypad programming sequences is located at the back of the manual for quickreference.KEYPAD PROGRAM

22Since the KP-32 requires 2 setup pages, it uses the main page assignments and also one expansion page(Figure 3). The EKP-32 uses two additional expa

23Display Requests Using ScrollingThe display requests described previously can also be accessed using scrolling. Scrolling also offers severaladditio

24☞ To display setup page assignments at any time, see "Display Setup Page Assignments", 21.KEYPAD PROGRAMMING, ASSIGNING INTERCOM KEYSGener

25 5 All call (talk level 1 only) 6 DIM (talk level 2 only, for point-to-point key, must enter 00 first) 7 Auto table (listen only, when talk

264. Press the talk or listen key to which you wish to copy. The name of the key assignment should appearin the display above the key.☞ If a key will

276. In single-step mode, use the ↑↑ ↓↓ keys to make your final intercom port selection.☞ If you cannot locate the destination that you are looking

28THE KP-32 MENU SYSTEM☞ A chart of the menu system is located at the back of the manual for quick reference.MENU SYSTEM, MENU ACCESS1. Clear all name

29keypanel. In this case, use the ↓↓ and ↑ ↑ keys to scroll through the list of names. You can then pressthe Call waiting key to ask the person at

3End-User License Agreement for Telex® SoftwareIMPORTANT - Please read this document carefully before using thisproduct.THIS DOCUMENT STATES THE TERMS

302. Tap Menu3. Tap ↓↓ to scroll down to the menu.3. Tap PGM or FWD to enter the menu.☞ If you do not have a trunking intercom system, skip to step

318. Tap PGM or FWD to select the assignment.9. should now display in the Call waiting window. Press ↓↓ or ↑↑ if necessary toselect a different op

32Key Assign Menu, Pt-to-PtAssigns a key that talks or listens to another intercom port. Note that some pt-to-pt destinations may benon-keypanel devic

33• AutoFollow (AF, for listen keys only)• Auto Listn (AL, for listen keys only)• Auto Mute (AM, for listen keys only)• Auto Recip (AR, for listen

341. Press FWD or PGM to select in the Key Assign menu.2. displays. All key gains are now reset to the default level.3. Tap CLR to quit.☞ You do not

355. displays (store auto dial number 1). To store a different auto dial number, press ↓↓ or ↑ ↑ to select the desired auto dial number.6. Tap PG

36Clearing a key group1. Select , then tap PGM.2. displays. To select a different group, press ↓↓ or ↑↑ .3. Tap PGM.4. displays.5. Tap the current

37SERVICE MENUService Menu, DimThis item causes the speaker or headphone level to diminish by a specified amount whenever a talk key isactivated.1. Se

381. Select , then tap PGM.2. displays. Press ↓↓ or ↑↑ .to display any of the following items:3. Refer to one of the following paragraphs for furth

393. Tap PGM.4. displays.5. Tap PGM.6.→ displays. The arrow indicates that gating is now selected.7. Tap CLR to exit.8. Run "Service Menu, Save C

4TABLE OF CONTENTSDESCRIPTION AND SPECIFICATIONS ...6DESCRIPTION...

403. Tap PGM.4.→ or d isplays. If an arrow displays, this indicates that the mic signal is currently beingrouted to the destination that you selecte

41Figure 4. LCP-32 correspondence to KP-32 and EKP-32 keysFor example, you may not want to use LCP-32s with the KP-32 but do want to use them with an

4210. Tap the intercom key that you want to assign. This is the key that will activate when the GPI inputactivates.11. Tap CLR to exit, or BACK to bac

43Adding or Removing a GPI Output Key Assignment1. Select , then tap PGM.2. displays.3. Press ↓↓ to display .4. Tap PGM.5. displays.6. Press ↓↓ or

441. Module ID number is displayed here.2. Select the correct module ID number with these keys (see below). ↓↓ ↓↓ ↓↓Call waitingMicHeadse tVo l.

45If latching is enabled, tapping up or down on any intercom key, or the Call waiting key, will cause thecorresponding red LED to light. This verifies

46GLOSSARYAll CallFor talk key assignment only. Activating an All Call key will also activate alltalk keys to the left of the All Call key (up to, but

47RTS ADAM, ADAM CS, and Zeus Intercom Systems do not actually usecrosspoint switches, but use a technique called time division multiplexing(TDM), in

48listener at a particular intercom output port normally hears an audioprogram source connected to a particular intercom input port. A keypaneloperato

49specific common activity and they need to talk and/or listen to eachother all the time. Keypanels are almost never members of party lines(although t

5GLOSSARY ... 46INDEX...

50It is also possible to adjust the listen gain for any specific intercom portwhen listening to any other specific intercom port. This is called the p

51Talk Level 2Talk level 2 is used with stacked talk keys. A stacked talk key activatestwo types of communication at once. For example, a stacked talk

INDEXAC Power, 7ADAMedit, 6, 9, 13, 14, 15, 16, 17, 19, 23, 25,26, 27, 29, 32, 33, 43, 46, 47, 48, 49, 50Address, 10, 21, 23, 29, 43, 44, 49, 54, 55,

53Microphone, 7, 8, 43, 58Muting (MUTE), 24, 46, 56NUM KeySee Also, Intercom Port, Point-to-Point, 24, 56Option, 14, 15, 16, 20, 29, 34, 35, 36, 44Opt

54Table 1. Address number vs intercom port numbers for 8-Port Audio I/O Cards (ADAM andADAM CS Intercom Systems)Address Card Numbers (bold headings) a

55KP9X KEYPAD SEQUENCE QUICK REFERENCEKP9X DISPLAY SEQUENCESFUNC DISPLAY 0 . Diagnostics mode.FUNC DISPLAY 1 . Display port number.FUNC DISPLAY

562. Select the key assignment type:NUM Intercom port.PL Party line.AUTO Auto function.FUNC SLIST Special list.FUNC IFB IFBFUNC ISO Camera ISOFU

574. Activate the TIF talk key (talk LED turns green). The "ON" LED at the TIF-951 will activate, and youshould hear dial tone at the KP-32.

58KP-32 MENU SYSTEM QUICK REFERENCEMENU ACCESS1. Clear all names from the Call waiting display (if not clear) by tapping "up" one or more ti

6DESCRIPTION AND SPECIFICATIONSDESCRIPTIONThe RTSTM Model KP-32 Keypanel fits in a standard 19" rack and is 2 rack spaces high. It has 32 leverke

7SPECIFICATIONSMicrophone PreamplifierAudio Input Level (at 1 kHz):Electret Mic: -42 dB, 150 ohmsDynamic Mic: -60 dBm, 150 ohmsOutput Level (to matrix

8Headset ConnectorConnector Type XLR5 femalePin-out Pin 1: Mic lowPin 2: Mic highPin 3: CommonPin 4: Headphone left highPin 5: Headphone right highPow

9INSTALLATIONOPTION DIP SWITCH SETTINGSSwitch 1: Latch Enable/DisableDefault setting = Open: Enable.Description: An intercom key can always be turned