RTS XCP-ADAM-MC Instalační příručka stáhnout pdf (Strana 7)

Once an input has been assigned to a key, it is then neces-

sary to define a device to be activated by that key. This is

accomplished in the keypanel edit screen for the port to

which the digital input was assigned. (See “Key Panel

Setup: Key Assignments and Key Restrictions” in the

CSedit User Manual.)

The UIO-256 relay outputs are programmed using the re-

lay edit screens in CSedit. See “Using Relays” in the

CSedit User Manual.

9.4 Connecting to a Trunking Master

Controller

1. Connect from J2 of the Master Controller Breakout

Panel to any available data port of the trunking sys-

tem. Use an RS-485 data cable wired as shown in the

ADAM-808 installation drawing on page 35.

Note

To use the same PC for configuration of both the ADAM

system and the Trunking Controller, either use an RS232

switching box, or use separate COM ports on the PC.

(CSedit and CStrunk only recognize COM1 and COM2.)

2. Interconnect one or more intercom audio ports between

the intercom systems. These ports will be used for

trunking communication only. See the ADAM-810

drawing, page 37, for wiring diagrams of the special

intercom cables required for trunking audio intercon-

nect.

Note

The number of intercom ports that are interconnected

should be based on the number of persons that need to

communicate with other intercom systems, and on the

amount of intercommunication that will normally occur.

The trunking system will automatically allocate the inter-

connected lines to personnel as needed, but if frequent

busy signals are encountered during normal use, it may be

necessary to allocate more trunk lines. Also remember

that it is not always necessary to interconnect two inter-

com systems if they are both connected to a third inter-

com system. The trunking system can create a

communication path by “cascading” through the third in-

tercom system. However, this type of communication can

tie up two or more trunk lines, and could create more

busy signals for other users.

3. Within each intercom system, run the CSedit intercom

configuration software. Turn on all restrictions for

each intercom port that is being used as a trunk line.

See “Key Panel Setup: Port Information" in Section 2

of the CSedit User Manual.

4. Also using CSedit within each intercom system, remove

scroll restrictions for each intercom port, party line

etc. that will be made available for key assignment in

other intercom systems. For keypanels, belt packs

etc. that are connected to individual intercom ports,

this is accomplished using the same setup screen that

you used in step 3 to restrict trunking ports. For party

lines, IFB’s etc. refer to the numbered step regarding

restrictions under “Creating a Party Line”, “Creating

an IFB” etc. in Section 2 of the CSedit User Manual.

5. Run the CStrunk Trunking Configuration Software, and

configure the trunking system as described in Section

2 of the CStrunk User Manual.

6. Within each intercom system, assign keypanel keys as

required to communicate with destinations in other in-

tercom systems. See"Key Panel Setup" in Section 2

of the CSedit User Manual.

10 Intercom Port Connections

10.1 General Information

Typically, devices are connected to individual intercom

ports using Station Breakout Panels as shown in the

ADAM-101 through ADAM-108 drawings. Depending

on the type of breakout panels being used, the individual

intercom stations will utilize either RJ-11 modular style

intercom cables, or 9-pin D-sub cables. Wiring diagrams

for both are shown in the ADAM-810 drawing, page 37.

Each intercom port supplies two pins for audio input, two

for audio output, and two for data. All audio connections

are balanced, dry lines. All audio inputs and outputs are

set for unity gain by default: whatever level is applied at

an input will be supplied at the output. Input and output

levels may be adjusted for individual ports if required.

This may be accomplished either from CSedit or from in-

dividual keypanels.

Various types of intercom stations are generally con-

nected to the intercom ports, but other types of audio de-

vices could also be connected. For example, a program

source could be connected to the audio input for an inter-

com port, and in this case the audio output and data pins

are not used.

The data wires for an intercom port are used to send and

receive control information between the connected device

and the ADAM master controller. The data wires are only

used by keypanels, by the TIF-951 Telephone Interface,

and by the CDP-950 Camera Delegate Panel. The type of

data transmitted includes key pressed information and dis-

play information. For example, when a key is pressed on

a keypanel, this information is sent on the data wires to

the ADAM frame. The controller in the ADAM frame

ADAM Installation Manual 5

1 2 3 4 5 6 7 8 9 10 11 12 ... 40 41

Komentáře k této Příručce

Žádné komentáře

RTS XCP-ADAM-MC Instalační příručka Strana 7

Komentáře k této Příručce

Související produkty a manuály pro Systémy intercom pro domy RTS XCP-ADAM-MC