RTS CIF-612 Specifikace stáhnout pdf (Strana 26)

5.4.10.6

Connect signal generator to program input 2

(5106). Set generator for 100

and 4 volts AC

peak-to-peak (1.41 volts rms).

5.4.10.7

Check the AC voltage on bus wire connect-

ing pin 14 of the thumbwheel switches for 2.0 volts

AC peak-to-peak (0.70 volts rms).

5.4.10.8

Set the lower row of thumbwheels to 14.

5.4.10.9

Connect station 2 to BOP220 output

(5101).

5.4.10.10

Listen on channel 2 of station 2 for the 100

tone. Move station 2 to BOP220 output 2 (5102)

and listen for tone. Repeat for each output.

5.4.10.11

Connect signal generator to program input

3 (5107). Set generator for 10

kHz

and 4 volts AC

peak-to-peak (1.41 volts RMS).

5.4.10.12

Check the AC voltage on bus wire con-

necting pin 15 of the thumbwheel switches for 2.0

volts AC peak-to-peak (0.70 volts RMS).

5.4.10.13

Set the lower row of thumbwheels to

15.

The upper row stays at 12.

5.4.10.14

Connect station 2 to BOP220 output

(5101).

5.4.10.15

Listen on channel 2 of station 2 for the 10

KHz

tone. Move station 2 to BOP220 output 2

(5102) and listen for tone. Repeat for each output.

5.4.10.16

With the tone still connected to program 3,

set the upper row of thumbwheels to 15. With the 0s-

cilloscope, check between phis

and 2 of

all

the XLR

output connectors on the BOP220 for 2.0 volts AC

peak-to-peak (0.70 volts RMS).

5.4.10.17

Connect the tone to program input 2

(J106).

Set the upper row of thumbwheels to

14.

With the oscilloscope, check between pins

and 2 of

all XLR output connectors on the BOP220 for 2.0

volts AC peak-to-peak (0.70 volts RMS).

5.4.10.18

Connect the tone to program input

(J105). Set the upper row on thumbwheels to

13.

With the oscilloscope, check between pins

and 2 of

all

XLR output connectors on the BOP220 for 2.0

volts AC peak-to-peak (0.70 volts RMS).

5.4.11

CAMERA

OUTPUTS

TEST

With the

"TW"

power supply still connected to Jlll

on the SAP1626, connect station

to power supply

channels

and 2.

Build a camera output test furture. Use Figure 5-1 as

a guide. Connect wires to a male

pin connector.

Strip,tin, and label the wire ends. Plug the connector

into 5108 on the back panel of the SAP1626. Connect

the oscilloscope common lead to pin number

5.4.11.1

Set

all

CAMERA

thumbwheels to

Touch scope probe to pin 14. Talk on station

chan-

nel

and verify audio. Move upper

CAMERA

thumbwheel to

and check that audio stops.

Touch scope probe to pin 20. Talk on station

chan-

nel

and verify audio. Move lower

CAMERA

thumbwheel to

and check that audio stops.

Repeat for cameras 2

6, pins 15-25.

5.4.11.2

Set

all

CAMERA

thumbwheels to

Touch scope probe to pin 14. Talk on station

chan-

nel

and verify audio. Move upper

CAMERA

thumbwheel to

and check that audio stops.

Touch scope probe to pin

20.

Talk

on station

chan-

nel

and verify audio. Move lower

CAMERA

thumbwheel to

and check that audio stops.

Repeat for cameras 2

6, pins 15-25.

5.4.113

Set

all

CAMERA

thumbwheels to

Touch scope probe to pin 14. Talk on station

chan-

nel

and verify audio. Move upper

CAMERA

thumbwheel to

and check that audio stops.

Touch scope probe to

20.

Talk

on station

chan-

nel

and verify audio. Move lower

CAMERA

thumbwheel to

and check that audio stops.

Repeat for cameras 2

6, pins 15-25.

Connect station

to channels 5 and 6 of the

"TW"

power supply. Connect the

"TW"

power supply to

Jlll input on SAP1626.

Page

5-4

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 71 72

Komentáře k této Příručce

Žádné komentáře

RTS CIF-612 Specifikace Strana 26

Komentáře k této Příručce

Související produkty a manuály pro Systémy intercom pro domy RTS CIF-612